Sew and trim the corners. Measure the length of each side and add 1 inch for seams. *See more pictures of these steps on my blog. First use hot glue to join the two cut pieces. Fold the seam along the corner by pulling the fabric tight towards the center. Just fold the fabric with the cord in the fold and stitch as close to the cord as possible. I used 3/4-inch plywood for my ottoman top. Watch how to do this part.

Trace your lid on another piece of fabric. Start stapling the fabric at one corner, but make sure to stretch the fabric tight as you staple it to the ottoman top. The best way to calculate fabric for upholstery is to talk to a local upholsterer. Lazy Ottoman Recovering Tip #2: Don't sew the seams. To make the base for your ottoman attach the two longest side sections to the top with angle braces and 16mm screws. Fold the material in half and mark off width and length dimensions. Staple the remaining sides down. I cut the fabric into lengths that were about six inches longer than the fabric . Step Three Glue and Screw the 4 - 14 boards to the 22's, with a 1/4 setback from the front of the 22. Place the fabric right side down on your work surface, then lay the pad and wood seat on top of that. The original leather on the ottoman was stitched on the corners. Then pin and sew the welting around the top and bottom edges of the loop. Attach the foam to the top of the ottoman using spray adhesive.

Place the ottoman cushion on top of the fabric. Continue around the perimeter of the bench. First, measure your ottoman on the top from left to right. Fold the seam along the corner by pulling the fabric tight towards the center. Using a tape measure and pencil, mark six 16-inch sections, four 8.5-inch sections, and one 46.5-inch section on the one-by-four. The distance between the straps will depend upon where the coil springs will be sitting and will probably be closer together . First, cut the pillow case along the seam both vertically and horizontally. Finish the corners with a nice mitered fold and then staple it in place. When you get to the corner you'll want . Pull your excess fabric tightly to the center of the corner and secure with a few staples. Measure the bottom two rectangles and cut out two pieces of each size. Then rotate around the top stapling, pleating where necessary, keeping the fabric tight and even. The last step in this how-to upholster a footstool project is to finish off the underside of the footstool. 1. Slide the cover onto the ottoman, and then use the upholstery tacks or heavy duty staples to secure the cover in place. 3. Unfold the second fold so that only the raw edge seam allowance is folded . Cut excess fabric outside of the staple line. Cut a piece of thick upholstery foam to fit the top of the ottoman. Option 2 - Fold two triangles and tuck one under each side. Repeat the process along the back edge and sides. 3. Then measure the depth of the sides and add on a few inches to ensure that you've got enough fabric to staple to the base. Then I tucked the corners in to create a finished look. The original leather on the ottoman was stitched on the corners. Then trim the edges down so that the flap still connected to the corner is about two inches wide. 2. Using scissors, trim around the fabric leaving 4-5 inches on every side. Apply hot glue along the edge, and then pull the fabric onto the glue. Cut the fabric to size and make a 1-inch fold around all four sides. Keep the fabric taught and smooth it out with your hand as you go. Staple the fabric onto the cushion frame. Leave a half-inch seam allowance on all seams. Use fabric scissors to ensure a straight, even cut. Step 6: Reattach the feet to the ottoman. Add another row of staples or tacks. I first basted the corners and then placed the fabric back onto the cushion to make sure it fit properly before stitching the corners in place. The folded edge will be inside the frame of the footstool . How do you sew a corner on fabric? Tips: To protect hardwood floors, add a felt pad to . Using heavy duty scissors, cut the fabric or leather very close to the staples, but stop cutting right at the corner. 3. Procedures.

So, I created my "no-sew ulphostery corner". First, cut the pillow case along the seam both vertically and horizontally. Iron the edges to make a clean seam. Use this measurement to add a . I then trimmed the excess fabric near the seam and pressed the seam open. Lazy Ottoman Recovering Tip #2: Don't sew the seams. You end of with tailored corners like . Then pin and sew the welting around the top and bottom edges of the loop. You will need to use a heavy duty staple gun. Take the ottoman top and lay it down, top side down, on the upholstery fabric. Tip: Fold each piece that you'll be sewing together in half and mark with a fabric marker. Step 2 - Sew Corners. Leave about an inch or so loose without staples near the outside edge of the corner. Remember to fold in the corners to get a clean cover. 4.) Depending on the type of furniture you have, it may be difficult to calculate the amount of yardage you need to recover a chair, sofa, ottoman, or stool. At the corners, make a box pleat (like you're tucking in the bottom corner of a bedsheet) - fold the fabric corner around to one side, then flip the fabric flap down to cover the excess and to form a straight line at the corners. Give yourself a few inches of extra fabric when you cut, but start trimming so that you don't have as much fabric to deal with. Pull your left side to the right making a clean fold and secure with a few staples. Write down this measurement as your width and be sure to add a one-inch allowance to accommodate all the hems and seams. This can be easily done with a basic Philips head screwdriver. Fold in half again and mark. Position your side strips face sides together and sew your corner seams with 1/2 inch seam allowances. Stapler. I began by removing all of the hardware and screws. This creates a triangle that you will trim. Use a single edge razor to cut away excess fabric along the staple line. This will create a flap of fabric at the corner to cover the corner effectively. Cut a long length of upholstery thread and tie to button. "This is a way to cut corners," says . Write this measurement down, including an inch allowance for hems and . I painted the feet on mine with 3 coats of white chalk paint, Amy Howard One Step Chalk Paint in Bauhaus Buff. Remove the fabric and sew a straight stitch where you pinned. No Sew Ottoman Reupholstering. Disassemble the top of the ottoman and trace onto your upholstery fabric, leaving about a 5-inch buffer on each edge. Just fold the fabric with the cord in the fold and stitch as close to the cord as possible. I opted to keep it simple and came up with a no-sew way of reupholstering it. Place the rug facedown and then place the bench on top of the rug. Then cut with the chop saw. Lay the fabric out so you have one long piece.

Measure the top of the footstool foam, and add 1 inch to the length and width. Profess. Place the ottoman cushion on top of the fabric. The remaining excess fabric is then tucked, folded and pulled around each side of the corner and stapled neatly into place on the underside of the upholstered ottoman.

Sew the four sides of the cushion end-to-end, to make one long loop. Add Tip.

Then use spray adhesive to adhere the foam to the top of the plywood. The 16-inch sections will be the vertical legs of the base, and the 8.5-inch sections and the long piece will be the bottom of the base. Step 1 Make a diagonal cut in the corner of the fabric toward an inside corner of the cushion, stopping about 1 inch from the cushion. Pull out the flap of fabric. Cut any excess fabric from the bottom, ensuring that you leave 3 - 5 cm (2 - 3 in) overhang. I cut a piece a little larger than I need and fold over one edge. I began by removing all of the hardware and screws. Place upholstered seat on bench legs and carefully check its position to ensure the seat has the same reveal, or overhang, on all sides (Image 1). Step 5: Add the black fabric backing to the underside of the ottoman using staples. DIY TIP: Make sure you place the screw tip in the exact centre of the hole in the brace, or it will not be straight. Step 1: Position the fabric over your ottoman (or stool or bench) to where you like the print positioning on top. 5. Next, measure your ottoman from front to back, which will give you the length of the ottoman. It should be a tight fit. It is a black (usually) fabric that gives a professional look to the piece. Pull taut and staple the batting on the underside of the ottoman frame. Add a row of staples or tacks. Then move to the right corner and smooth it out and add a staple and do the left side as well. Start stapling the fabric at one corner, but make sure to stretch the fabric tight as you staple it to the ottoman top. You could definitely sew a nice cover, but this took about 10 minutes to finish. Leave a half-inch seam allowance on all seams. 5. On to the lid! Pull the unstapled corner of your fabric up so that it matches the corner of your frame. I also decided to add nail heads to give the ottoman a little extra detail. 9.

Place the fabric back onto the ottoman with the wrong side facing up, and pin the opposite two corners. Pull the fabric tightly and fold over the edge of your ottoman, just like you would when you are tucking in the corner of your bed sheets when making your bed. When you get to the corner you'll want . Once sized, place the panel onto a piece of black fabric. Recovering is simply putting new fabric over the old fabric. Tuck the fabric and batting that extends past the top of the ottoman inside, folding in the corners.. Reattach Top. On the corners, I folded the extra fabric inside, like we do in a gift wrap. Using scissors, trim around the fabric leaving 4-5 inches on every side. Staple the corner in place on the inside of the ottoman. Draw around the topper to mark out the top surface of the fabric. All three layers should be front side down. I sewed these strips together using a 1/2-inch seam, and then pressed the seams open and flat with a steam iron. Ottoman in 2021 Reupholster, Outdoor ottoman, Outdoor decor from www.pinterest.com. Finally, measure from the top of the ottoman to the bottom edge of the ottoman frame or to the floor if the slipcover is to reach the floor. DIY Upholstered Ottoman Plans from Scratch - Build Steps Step One Cut all of your wood to size, except the 1/2 x 3/4 Moulding. Step 1: Measure and Cut the Base. How to Sew Boxed Corners - Method 2 (French Seams) This method involves sewing the WRONG sides of your fabric together and pressing it flat with a hot iron.

Place it back on the ottoman to ensure it fits well and adjust the seams accordingly, if necessary. Flip the seat over several times to check the pattern as you go. Pull your right side to the left making a clean fold and secure with a few staples. 4. I used 3-inch high-density foam for mine, purchased at JoAnn Fabrics during a 50% off sale. from the corner. Trim excess fabric and keep securing. First, cut your plywood to the size you want (or have Home Depot or Lowe's do this for you). Tip: Fold each piece that you'll be sewing together in half and mark with a fabric marker. Rug. Trim the webbing off leaving about 1 1/2 to 2" to fold over. Create a cover for the topper using upholstery fabric. Back stitich or sew twice the top and bottom. It will all depend on the type of fabric you want to purchase and the type of furniture you want recovered. You will be pulling the fabric taut during the process, so you need a fabric that can handle this and will not rip or tear. Repeat at each corner. Staple one side, then go to the opposite side. Lay the fabric out so you have one long piece. You'll cut both sides at one time. Make sure to smooth and tug at the fabric to ensure it is wrinkle free and slightly taut. Step 2: Assemble the Base. There is probably a better way to do this, but I sort of figured it out . . Ask Question. Start with one side and work your way around the ottoman, pressing down on the fabric as you go.

2. I also wanted a fabric that was easy to clean . Many a woodworker has made a chair that needs a comfortable seat - and then met their match by trying to fold an upholstered corner that looked good. Center your rug on the ottoman and start stapling on one side leaving about 3 open from the end. Pull the cover over the padded frame and tack underneath. At the back of the ottoman use a button to thread through. But it didn't look easy - and this mama likes the easy way to do stuff. Step 1: Choose your fabric wisely. Stop 2 in. Step 4: Add the liner.

You may have a thick fold on the corners. I did not get exact dimensions when I did this - I just cut out enough fabric to make it work. Iron the fold on the cover for a clean look. Place the ottoman top on the fabric and staple all around by stapling opposing sides while pulling the fabric tight as you go. Make sure you have enough fabric on all sides to staple underneath. Fold the fabric over the point of the corner, pull it tight and then secure it to the underside of the bench. Ottoman in 2021 Reupholster, Outdoor ottoman, Outdoor decor from www.pinterest.com. Pull the corner inwards towards the center of the ottoman while sliding the excess fabric on either side underneath it. Thread both ends through upholstery needle. Staple at least every inch, with more staples in the corners. Tuck the unfinished edges in so they won't be exposed. Place a section of batting-4 in. 4. I laid it on top of my fabric and cut around it leaving about 6 on each side to fold over and around to the other side. The bottom only had fabric around the sides. wider in all directions than the size of your chair seat-on a flat work surface, then set your foam and seat on top.

. No sewing involved! Our leather ottoman somehow contracted a hideous skin condition (peeling and cracking and just looking a hot mess), so I tackled the job of recovering it. First, it's important to understand the difference between recovering and reupholstering. [8] 6. Sew the four sides of the cushion end-to-end, to make one long loop. Install all the webbing going one direction then weave the pieces going the other direction.

Cambric is also called a dust cover. Cut the fabric so that the sides are long enough to wrap the corners and there is enough left over to staple. Step Two Put 2 Kreg Jig Pocket Holes at each end of the 4 - 21 14 boards. Each ottoman may be a bit different but on mine, the feet were attached with 2 screws on each side. Now, go directly to the opposite side and do the same thing. Fold the corners in either by creating two darts on each side or by doing a square fold. Push needle through from the front to the back. Pull the fabric over one side, and fold it onto the bottom of the ottoman. Step 2 Make two diagonal cuts 1/2-inch long from the first cut to finish the "Y" cut in the fabric. And that looked nice. 3. Write this measurement down and add an inch allowance for hems. #BudgetUpgrade.

There will be a little excess fabric at the corners and you will make a nice little fold, one on each side of the knee and staple in place. Fold the corners in either by creating two darts on each side or by doing a square fold. If your ottoman has a top cushion, then you will need to add another inch allowance to cover the side of the ottoman up to the top frame. Fold in half again and mark. Then pull the flap very tight and lay it down .

Smooth the liner fabric along the inner storage box. Instructions: 1. Pull the unstapled corner of your fabric up so that it matches the corner of your frame. You should have 2 squares (or rectangles) to cut out.

Then sew the seam again, this time with the RIGHT sides together. Staple at least every inch, with more staples in the corners. Pull the fabric tightly and staple in place. Next, I cut the strips to cover the welt cord. 2. Cut excess fabric outside of the staple line. I cut the fabric into lengths that were about six inches longer than the fabric . With the top sewn together, I cut it so that it was the exact size of the top (mine is 22 x 17) plus a 1/2-inch seam allowance on all four sides. And that looked nice. Using a button allows you to secure the thread. Place the circle onto the underside of the lid and trim it to fit inside the corded edging using tin snips or scissors. Leave a few inches unstapled at the corner. Step 3. You will need to make sure that you choose an upholstery fabric when covering your bed, so stay away from selecting thin cotton or linens. Lay the fabric face-down and position the topper on top. Staple from the center out a few staples in each direction. Pull the fabric taught and use the staple gun to adhere it to the underside of the lid. Cut the inner lining fabric to size - making allowance for the sidewalls and some extra to fold in. STEP 5. Fold one side of the upholstery material over its respective bottom or back edge over the project, then staple the entire area -- aside from the corners -- stopping about 2 inches away from each. Spray the inside of the frame with spray adhesive. Cut out a circle of fabric 3-4 inches larger than the seat. Pull the loose fabric straight out at the corner of the ottoman, fold it around the corner to the left or right and press the cut edge of the fabric into the hot glue.

Sewing would have taken much longer. Step 1: Remove feet from ottoman.

Once the screws were removed, I was able to simply unscrew the leg from the ottoman that was held in place by those bolts you see on the end of the feet. After those sides are done, move to the ends and tuck in the corners of the already stapled sides. Pull tightly. Step 2: Staple the fabric underneath on one of the sides. Continue around the perimeter of the bench. Measure the height of the side of the foam and cut four strips of fabric to this height plus 3 inches. So, I created my "no-sew ulphostery corner". Put the bench on the rug where you want the design on the rug to be. Fold the edge of the fabric back 1cm ( in) then fold again to hide the raw edges, then using (staple gun/tacks) secure the . Creating neat and professional corners on upholstered projects is a challenge, but also a must. See Basic Cutting And Sewing. Here's a step by step tutorial to show you exactly how to get. Step 3: When you get to the corner, tuck the fabric under to make a straight fold so . Step 3: Wrap It Like a Gift The corners may be a bit tricky. But it didn't look easy - and this mama likes the easy way to do stuff. Fold over one side of the fabric and staple every few inches. Cut out a piece of fabric that will wrap around the outside of the lid. Pull the corner inwards towards the center of the ottoman while sliding the excess fabric on either side underneath it. Secure the fabric to the bottom using a few staples. Start stapling! How To Make A Tufted Coffee Table Ottoman. Fold over one side of the fabric and staple every few inches. [8] 6. Use fabric scissors to ensure a straight, even cut. Holding the seat in place with one hand, flip the bench over, then reinstall the same screws you removed in the first step (Image 2). I stapled following the order of the numbers in the photo below. Cut out your shape and then trim it so the fabric is a bit smaller than the lid. Next, spray adhesive onto the top of the foam, then cover it in batting, wrapping the edges down over the sides.